Sheathe house metal siding do it yourself

For metal it is 1.9×10 -5 / o C, and for polyvinyl chloride (50) · 10 -6 / ° C.

The starting level is fastened in 300-400 mm increments.

2. Installation of complex internal and external corners, as well as complex strap H-connector

If you prefer to use complex additional elements to metal siding – then they should be installed after the starting bar. The pitch of mounting screws or nails – 200-300 mm. This is due to the fact that the parts have a rather complicated structure (geometry) and to ensure their reliable fastening will help more frequent drilling of self-tapping screws.

  Sheathe house metal siding do it yourself

H-connector complex H-connector complex

The corner is external difficult

The corner is internal difficult The corner is internal complex

Good to know. Angle sizes may vary by manufacturer.

The installation of the H-connector and complex angles is shown in the figure.

Installing the H-connector and complex corners

The material is prepared for the site www.moydomik.net

Council As a rule, when installing metal siding, simple angles are used, since they are much cheaper, easier to install, easy to replace if necessary.

Door and window openings are also framed at this stage. For this purpose, a slope plate or a platband and an ebb bar are used.

Slope or platband Slope or platband

Low Tide Plank Low Tide Plank

Cladding of window and door openings The width of the casing depends on the depth of the opening and the thickness of the batten for siding. The low water bar is mounted at the bottom of the window opening.

Try to mount all the strips on the same level, this will give a beautiful view of the facade of the house.

Good to know. To lengthen the bar it is enough to impose the top on the bottom with an overlap of 25 mm.

3. Installation of ordinary metal siding strips

The installation of metal metal siding stripes is identical to the installation of vinyl panels. In the presence of complex corners, a bar is inserted between them and fixed on the starting bar with self-tapping screws. In the same way are mounted and the remaining strips. Step of installation is 200-300 mm.

Council The next row of panels is installed on the previous one until the lock is clicked with tension. If necessary, the lower part of the strip can be tied up with a mallet.

Fastening hardware Fastening fasteners better also in the middle of the nail holes.

The joining of the strips takes place with the use of a complex H-connector or a simple latch.
If you do not plan to use the H-connector and the overlay you can mount the strips of material overlap. At the same time it is important to cut off the lock from one panel in order to ensure a reliable connection.

The overlap should be at least 25 mm to prevent the ingress of dirt and moisture.

Helpful advice. Constantly monitor the horizontal of the installed slats using the building level. Optimally do this every third row.

If you did not install complex corners, then the panels are mounted on the starting strip. A strip is cut the same length as the width of the frame under the metal siding. According to the results, in the place of the corner joints you will have butt joints, which will then be closed using simple corners.

Fastening the last board is as follows: the penultimate row of panels is mounted, then the finishing bar. Then the remaining strip is cut to the desired length, hanged on the lock until it clicks and lead to the bending of the finish bar.

Finishing plank Finishing plank

4. Installation of simple corners and H-connector

Simple additional elements are mounted directly on the front side of the metal siding.

H-connector simple, patch plate or splat N-connector simple, patch plate or splat

The outer corner is simple The outer corner is simple

The inner corner is simple The inner corner is simple

Installation of a simple outer corner is shown in the figure.

Council Unlike vinyl siding, additional elements for metal, can be ordered as you need. The only length limit. All of them are a maximum of two meters, this restriction is imposed by a bending machine. But you can make them in any configuration. The main thing is that the total width of all sides of the strip does not exceed 1250 mm (width of the metal sheet). Or 2000, but then the length of the strap will be 1250 mm.

For fastening simple additional elements, galvanized self-tapping screws with a gasket are used. They are drilled through the metal, so it is better to select the screws in the color of the front side of the panel.

Council Screws are easy to unscrew, so you can use rivets. In this case, the rivet does not penetrate the metal, but is mounted in a pre-drilled hole. Its diameter must be greater than the diameter of the rivet by 0.1 mm. The length of a rivet recommended by professionals makes 6 mm.

The pitch of fastening hardware in the corner depends on its width, but the angle is mounted on each side and is necessarily in a checkerboard pattern.

For example, if the plank width is 500×500 mm, then the fastening pitch should be 500 mm. And if the plank width is 700×700 mm, then fasteners must be mounted every 400 mm. The wider the bar, the harder it is, the more often you need to attach it.

5. Installing soffit metal siding

Spotlight without perforation Spotlight without perforation

Soffit is usually mounted on horizontal surfaces, facing downwards – overhangs, cornices, pediments.

The installation process is shown in the photo (2 options).

Types of compounds are shown in the figure.

Types of metal siding compounds

Installation of metal siding under the log

New on the market – metal siding imitating timber, log and block house.

Metal siding log Metal siding log Installation of metal siding under the log

The device of corners is similar to the arrangement of corners under a metal siding ship board.

Installation of metal siding – device angles

Metal siding timber Metal siding timber Installation of metal siding under the timber

Angles are mounted in the same way as in the two previous cases.

For these two types of siding, both horizontal and vertical fastening are appropriate.

Installation of metal siding – video

We hope that from the instructions given here you have received comprehensive answers to the question of how to mount metal siding with your own hands. Happy installation!

How to sheathe house metal siding do it yourself

To finish the facade of the house more and more often use metal siding. It consists of iron sheets with a thickness of 0.5 mm and a length of 0.5 to 6 meters, of various shapes, with a polymer coating applied. Sheets can also be made of aluminum, but they have not found such popularity because of not sufficient strength.

Siding is available in several forms: single board, ship or Christmas-tree board, and also in the form of a log (block house). Panels can have both a smooth surface, and structural (under a tree). Various prints can also be applied to metal siding, which will turn the panel into a real tree with knots or natural stone.

Just like all types of siding, metal siding is completed with various decorative elements. They in combination with the main panels will give the structure a beautiful and complete look.

It is possible to mount metal saidig with your own hands at any time of the year, unlike vinyl or plastic at low temperatures, it does not break and does not break. Practically does not change color (does not fade in the sun).

Required Tools

To finish the house with metal siding you need to have a set of the following tools:

Roulette – for accurate measurement of panels and additional elements

Square and marker – for obtaining and marking a clear right angle

Hacksaw and scissors for metal – for cutting siding and getting an even edge

Construction level – to observe the vertical when installing the batten and horizontal when installing the siding

Hammer drill – in the case of concrete walls for drilling holes

Screwdriver – to mount the siding to the crate screws.

Mounting crates

The most crucial and difficult step in finishing the house with a siding is to install the batten. On how much quality it will be made, on how much easier and more correct will be the installation process of siding.

Marking the wall under the brackets.

The crate is made strictly vertically from wooden bars or metal profiles. In terms of durability, of course, the galvanized metal profile has an advantage. It is L-shaped and is fixed to the wall with adjustable brackets. It is not recommended to use a profile intended for mounting drywall, as it is too thin and may not withstand the load from metal siding. Before fixing the brackets, a marking is made on the wall, and the holes of the required diameter for dowels or anchor bolts are drilled. The brackets have different lengths and are installed on the basis of their wall irregularities.

For additional insulation of the walls of the house between the crate fits insulation, which is attached to the wall with plastic fungi and vapor barrier closed.

Siding installation

After installation, the batten begins to install decorative elements: corners, ebb and sloping slats. To accurately install these elements with your own hands, you must use the building level.

Stepping back from a low tide about a centimeter, an initial level is mounted, to which the lower part of the panel is fixed, and the top is fastened with a screw with a press washer to the crate. The screw does not tighten tightly, but leave a small gap of 1 mm for possible thermal expansions of the metal. Sheathing home siding do it yourself upwards. Further, the panels are mounted in the same way between themselves and the crate to the very top. Every 2-3 rows, the horizontal position of the panels is periodically checked. The joint of the last row of siding adjacent to the roof is closed with a special decorative element. Regardless of the form of the panel, the installation process for siding is always the same.

Installation of metal siding with your own hands is not at all a difficult task and will bring a lot of positive emotions from the work done.

After installation of the main siding panels, final finishing of the window and door openings is carried out with decorative elements.

It is worth remembering. Metal siding should not be cut with a grinder, because when heated, the protective painted layer burns out and the siding starts to rust in this place.

Installation video metal siding

In order not to cut the siding panels once again, they can be ordered at the production of the required size. But decorative items, unfortunately, are available in a certain size.

The house, sheathed by metal siding with their own hands, looks no worse than a house decorated with natural materials, and in terms of service life will give them a tangible head start.

The service life of metal siding according to manufacturers at least 50 years.

Do-it-yourself metal siding installation

Currently, metal siding is gaining great popularity due to the fact that it is a material capable of providing a reliable, durable and wear-resistant exterior coating for the house. One of the most prominent representatives of this trend, thanks to its natural and aesthetic appearance, are products that imitate a log. Having high rates of resistance to the possible effects of environmental factors, the presented material does not require regular maintenance.

The relevance of the use of such a product, among other things, is due to the availability and ease of installation. In this article, we will describe how to do metal siding with your own hands (for timber, log), give step-by-step instructions, and also show diagrams, photos and videos.

Production

The material itself is made of galvanized steel sheets treated with a polymer composition simulating a calibrated log. The production of such products is based on applying a pattern to the profile using the technology “Printtech” (photo-offset), providing a realistic, as close as possible, natural colored tree trunk. Metal siding on the market is replete with its color range and is released in rolls with a sheet width of 188 mm, a profile height of 31 mm and a length of 80 to 800 cm.

Tools and consumables

Any construction operation and type of material involve the use of individual tools and components. In our case, the implementation of the planned plans will require the preparation of the following tools and accessories:

  • galvanized screws with a press washer;
  • dowel-nails;
  • construction level and roulette;
  • Bulgarian or scissors for metal;
  • screwdriver or drill with a set of bits and drills;
  • ladder.

An important aesthetic function in the decoration of the house by metal siding is played by additional parts: internal and external corners, slopes, docking strips, starting and finishing guides, the use of which allows to give the building a general completeness and a neat appearance.

Preparatory activities

Before each construction work, it will be useful for each person to study concepts such as installation instructions and practical advice from professional craftsmen, based on which step-by-step assembly will be carried out in the future.

In order to proceed with the installation of metal siding, first of all, it is necessary to analyze the surface on which the subsequent fastening will be carried out, and to ascertain its strength and reliability. The implementation of the task is achieved by visual inspection of the walls for the presence of external objects, mold or detached layers of plaster, in the case of which it is necessary to carry out their extraction and finish processing.

Otherwise, poor-quality preparation of the finishing surface may contribute to further deformation of the sheets and their destruction, which will entail carrying out repairs and monetary costs.

Marking

Having decided on the material, before fixing the brackets, the walls should be cleaned and put markings on them. Initially, using a broom or broom, you must remove the remnants of dust and dirt from the future surface. At the same time, to simplify access, it is useful to use a stepladder or a forest. In addition, the presented devices will be useful in the future, in the implementation of the installation of facing sheets.

Having finished with this event, the future surface should be drawn with horizontal and vertical lines at a distance of 50–70 cm relative to each other, and the points of intersection of these guides will later become places for brackets.

Correct marking is a pledge of durable and smooth finish, therefore, its application should be approached with special care, not forgetting to use the construction level and measure out the same intervals each time.

Placement of bracket supports

Placement of bracket supports

The mounting of the brackets is carried out along the perimeter of the entire surface from bottom to top, taking into account a number of important points:

  • depending on the type of surface being trimmed, we mount using 40-mm self-tapping screws or anchor bolts;
  • proceed to the placement of connecting strips – as a rule, these products consist of perforated metal sheets containing through cuttings of specified sizes and arranged in a certain sequence; in our case, since metal siding is planned to be placed under the log, the guide profiles are arranged vertically and fastened to the brackets with self-tapping screws 4.2 × 16 mm;
  • the guides are installed in such a way that there is a gap of at least 10 mm between them;
  • along the perimeter of the windows and doors, we additionally install guide rails;
  • in the corners of the construction, the installation of the profile is carried out taking into account the subsequent fixation of the corner bars.

Of course, an alternative to metal brackets can easily make wooden bars, the cost of which is several times less, however, metal products have a number of significant advantages, eliminating the subsequent deformation of the surface and ensuring reliable operation.

Installation of insulation

In the option of placing siding with insulation, plates selected materials are placed close to each other without additional gaps. In the case of several layers of the protective layer of the plate are installed in the gap of the joints. A windproof membrane film is located on the outer side and all layers are fixed with the help of dish-shaped dowels-nails. When installing this element, it is important to maintain the distance between the insulation and siding, which should be in the range of 25-30 mm.

Another option insulation – basalt wool. Named material is available in rolls, which greatly simplifies the installation procedure. In addition, unlike the foam, which is the cheapest type of insulation, the raw material from basalt allows the surface to “breathe”, providing the necessary ventilation.

This material is especially relevant when finishing a wooden house, since it is the wood that requires regular ventilation in order to avoid the appearance of snails, mold and fungus.

Facing installation

This event begins with the placement of the starting plate, which is the starting point and starting point for the subsequent installation of the siding panels. When fixing it, it is important to use the construction level and carefully measure out every millimeter, since the slightest deviation from the vertical can further lead to the curvature of the entire facing surface.

Metal siding under the tree

Sheets are fastened by means of metal brackets, screws and screws, depending on the available consumables. When placing the panels, do not install them tightly relative to each other, but leave a gap of 2-3 mm, which will ensure the subsequent adjustment of the installed surfaces.

Typically, the installation of siding type “block house” begin to carry out from the center, gradually moving to the corners of the building. In places of contact establish intermediate strips, as well as external and internal corners. In conclusion, the finishing bar is fixed, and the general facade of the house becomes similar to a “natural log house”.

As you can see, the installation of metal siding under the log – an effective and relatively affordable way to perform a unique insulated and aesthetic facade. In the case of the correct implementation of all operations, this material will function for a substantial period of time and protect your home from the harmful effects of the external environment.

In this video you can learn about the intricacies of installing metal siding:

The diagrams show the details of the installation of metal siding:

Sources: http://moydomik.net/materialy/oblicovochnye/301-montazh-metallosaydinga-instrukciya.html, http: //xn--80adrbabmmcdndvifem3a.xn--p1ai/kak-obshit-dom-metallosajdingom-svoimkru, http://kakpravilnosdelat.ru/montazh-metallosaydinga-svoimi-rukami/

Add a Comment

Your email address will not be published. Required fields are marked *