Exterior trim frame house

  Exterior trim frame house

Layers for plaster for a frame house are not different from layers of brick buildings

On sheets of foam plastic (you can take the thinnest – for example, 40 mm, since the skeleton, as a rule, already has mineral wool insulation) put a layer of special glue 4-6 mm thick. In the glue embed the mesh of fiberglass, performing the role of the so-called base reinforcing layer. On top of it is covered with a special quartz primer, which includes a filler of fine sand.

Facing plaster looks great with stone trim

Only after all these works have been completed can a layer of decorative plaster be applied, which differ in both color and composition.

Types of plaster for exterior:

  • acrylic
  • silicone
  • silicate
  • mineral
  • with various fillers

Important: Pay special attention to the quality of the reinforcing mesh. The adhesives give off alkali, which can dissolve the reinforcing layer, as a result of which the entire finish will become unusable.

Facade bricks for cladding

Facade bricks can also be of various types. It differs in its composition, color, additional inclusions. The most common types of brick for exterior decoration are:

  • silicate
  • hyper pressed
  • ceramic

Shades of brick for facing a frame house

The silicate brick has the most reasonable price, and the ceramic brick creates the most stylish and neat appearance of the building due to its surface. It can be smooth, glazed, or even matte. The hyper pressed brick has in its composition fine limestone and shell rock, which reduces the percentage of moisture absorption. Facade bricks are also divided into:

Holes have been created in the hollow brick front, providing an air gap. Therefore, such a brick retains heat better.

Hollow brick for facing buildings

Exterior cladding bricks can be made of various types of installation. Do not conduct finishing at low temperatures, as the solution may freeze through.

Calculate the number of materials needed for exterior finishing of frame houses in advance, since different batches of bricks may have a slight difference in shades, which will be noticeable after the plating is completed. After the exterior finish you can achieve a more even shade of masonry, if you treat the wall with a solution of 10% perchloric acid.

The brick is front red structural

Siding and PVC panels – cheap and tasteful

Siding is a panel for cladding of PVC buildings with a thickness of about 1.0 -1.3 mm. This is the cheapest and easiest way to finish the frame walls, which you can do with your own hands. Thanks to the sysnetic structure, siding is not subject to destruction, and allows you to forget about protecting your home for a long time. The skin does not deform, does not rot, the material does not like fungi and bacteria. The appearance of the house acquires neat European features, and the use of structural elements and different shades makes the house special.

Sheathing frame house siding

The frame house protected by a siding is not subject to corrosion. Lining material and all the lining can withstand sudden temperature changes from minus 40 to plus 60.

This is the best way to finish a frame building with a light foundation. The ease of finishing material does not give a large load on the walls and the foundation.

Installing a frame for house siding and paneling

Of particular popularity has gained this type of siding, as PVC facade panels under stone. PVC is a synthetic material, which is an excellent basis for imitation of natural stone, granite, brick, marble. In this case, this type of finish is perfectly washable, can be used to protect the basement.

Siding panels under the tile for the frame house

Panels with siding can be mounted on a frame that provides additional air gap. Additional ventilation contributes to the removal of excess moisture from the wall, retains heat. In addition, you can additionally use insulation.

Siding fastening for covering frame house

Sheathing of thermopanels with clinker tiles

Sheathe walls under the stone from the outside can be using thermopanels. The material is based on polyurethane, and performs not only protective and decorative functions, but also weatherization.

Clinker Thermopanel for Home Protection

The panels are fixed in a seamless way, thereby improving the properties of the finish. Clinker tiles, which create a beautiful exterior frame building, strengthens the walls, improving its shock resistance properties. The tile is not subject to abrasion, destruction and deformation by fungus, mold and bacteria. It is easy to clean.

The installation process takes place in several stages:

  1. Alignment of the geometry of the building. All walls should be smooth, and the angles of 90 degrees. If there is a deviation, it is necessary to use an additional crate of the frame house.
  2. Getting started with fixing base profile. The aluminum profile is mounted horizontally on the base of the frame structure.
  3. The next stage is angular thermopanels. Panel fastened to the base profile.
  4. Fix the panel with dowels or screws. Using the puzzle method we fold all the panels.
  5. With the help of polyurethane foam seal the panel, removing the gaps between them.
  6. Frost-resistant grout process seams.

The biggest disadvantage of this way of covering the skeleton is the price.

House, sheathed with thermopanels. looks like a brick

Facade tiles for brick, stone and other natural materials

With the help of wall cladding in this way, it is possible to protect the walls, change the design of the house, and give the old house a fresh look. On wooden walls, the tile is attached with a batten, otherwise moisture can penetrate from the tile to the wall. The tile should fit together tightly enough to avoid moisture penetration. Fixation occurs with adhesive solutions.

Facade tiles under the stone

Due to its composition, exterior tile has the following qualities:

  1. A variety of colors and shapes.
  2. Various reliefs and textures, gloss and dullness.
  3. Inexpensive and easy installation.
  4. An excellent choice for living spaces.
  5. The weight of the tile is quite light, so no additional foundation strengthening is required.
  6. It can be used for wooden frame buildings, as it does not make them heavier.
  7. Protects the wall from condensation and moisture penetration into the frame wall.
  8. Eco-friendly and harmless.
  9. Easy to repair.
  10. It may look like a decoration of elite varieties of stone, granite and marble, while the price is much cheaper.

Frame house sheathed with facade tiles

This tile consists of concrete, sand, plastic and coloring pigment.

Block house: a modern look of cladding

The use of a block-house for decoration will help to give your home a natural and natural look of a wooden house. It is a rounded log (or timber), inside which is a flat surface. The flat surface is mounted on the wall, with the result that the frame house takes the form of a house from a bar. Even inexpensive shield houses look like luxury housing.

Block house for trim house frame

In addition to its excellent appearance, the blockhouse has the following features:

  1. It perfectly protects the walls of the house from external environmental influences, including rain, snow, frost or the scorching rays of the sun.
  2. It is durable and not subject to destruction, thanks to modern high-quality impregnations.
  3. Exterior decoration of the block house of a frame house can be carried out with simultaneous insulation and sound insulation of the building.
  4. Quick and easy fixing can be done with your own hands.
  5. It is easy to replace one or more elements of decoration and repair.
  6. It is well combined in a tandem with plastic, brick, decorative plaster, giving a unique appearance to the frame house.

The frame house sheathed by a block house

The best video on the topic:

He inherited a house, and with it problems with dampness and mold. We took some steps to get rid of this filth, made repairs, warmed the facade, and the problem remained. But it turns out that we must also correctly select the material for the exterior of the house. And with this, we seem to have missed. But now, armed with knowledge, I will go and run around the consultants in the store. I will not hang noodles anymore.

Yes, this is correct, only if you have already established the fungus and mold, the most important thing is to kill it. And then you can change the materials. Otherwise, it will again appear through some time, even if the materials are now selected correctly.

Options for exterior finish frame house

The times when a tree was considered a warm material have sunk into oblivion. To prevent heat transfer through a wooden wall, its thickness should be at least 530 mm. for central Russia. The frames of individual houses are made mainly of wood, and sometimes metal structures are used, which makes the problem even more acute.

Therefore, the exterior finish of the frame house, besides the purely aesthetic, often performs an important technological function – it insulates wood (or metal) of the frame, which itself serves as a cold bridge. Of course, in this article we will also consider finishing options that ignore this fact, but we don’t have the right to mention it.

What outside trim frame house?

There are no special restrictions on the exterior finish of the frame house, there are some features of the application of one or another of its type, which we will inform you about. Frame houses revet:

with a wet facade system,

  • plaster;
  • stained;
  • put polymeric coverings.

You should make the decision on one or another type of exterior finish at home at the design stage, as some of them start at the foundation laying stage.

Facing frame house brick

If you have decided that your frame house externally should seem brick, then one of the options is covering it with natural brick. The main requirement here is the presence of a gap of 30–50 mm between the wall of the house and the inside of the brickwork and the air vents that ensure air circulation in this gap.

If this is not done, then moisture will inevitably condense on the inner surface of the brick during the cold season, which ultimately will lead to its accelerated destruction. Nor will she be spared by the outer enclosing material of the frame itself, which is often OSB or plywood.

Naturally, both the width and the bearing capacity of the foundation with this type of finish are adjusted upwards. In general, these are two different systems of housing construction and you should, when combining them, try to avoid hard ties between the frame that does not give shrinkage and the brick coat that sits down during the year. The consequences can be sad.

You can disguise this with a lowered overhang of the roof that is not connected to the brickwork. Also, either set aside for the time being the manufacture of exterior window and door slopes, or do not rigidly connect them with the masonry. It can be metal or plastic corners.

Facing a frame house with a tree

Correct lining with wooden moldings, such as block house, false timber, etc. will give your home a stylish look. Using them can also eliminate the outer lining of OSB, plywood or other slab material from the cake of the wall.

A textured wooden bar, well dried and treated with necessary impregnations, can be directly attached to the racks of the house frame from the inside, before laying the insulation layer, as well as on the clamps or through self-tapping screws – after it. Bearing in mind that the tree can be a cold bridge, we can recommend this mount in the case of the construction of a double frame, with a shift of racks relative to each other.

Also, the wood frame decoration with wooden elements can be made on the crate with a ventilation gap. It is important to remember that such a facade of your house will require periodic maintenance, which consists in the timely processing of paint-impregnating materials. And, of course, the tree will crack somewhere, somewhere in the sunny side the gap in the joints will increase. To this you just need to be ready, choosing this option of exterior home decoration.

Appeared recently in a large assortment of composite materials that mimic the structure of wood are completely devoid of these shortcomings, but those who are ready to pay a fairly large sum for their purchase will be able to verify this.

Exterior finish siding

This is the easiest option for finishing a frame house. If you have OSB or plywood outside your house, you can simply mount vinyl strips or ground siding cards on them. These materials practically do not change their geometry when exposed to heat and cold, siding itself will protect them from water, so you can avoid searching for complex and expensive ways to find beauty in your home. They also hold screws well.

The choice of the column-beam version of the frame allows not to use the outer sheathing of OSB or other materials at all, but to fix the siding directly to the frame posts.

If you want to insulate the wood of the frame, then fix the siding on the external vertical slats, bolted to the horizontal crate with a shift from the main beams of the frame and filling the gap between them with insulation.

It is important not to forget that outside the wall there should be a heater with a greater insulating ability, or the same as used in the cake of the wall, in order to avoid moisture condensation on the border of materials.

This type of decoration makes the house even more maintainable than its assemble by technology, finished with other types of materials.

In addition to plastic siding, you can use metal, but more often it is put on non-residential buildings.

Finishing of the frame house with thermopanels

Thermopanels are different. In terms of dimensions, materials, type and method of attachment. But one thing unites them: the presence of a layer of insulation and the outer finishing layer. Insulation can act as polyurethane foam, polystyrene foam, dense basalt.

Outside it can be: clinker tiles or clinker bricks, thin polymer concrete slab, imitating various natural finishing materials. This layer can be painted in bulk or require staining after installation and filling the joints. Options for the performance of thermopanels – the mass, you will always find in your region a few to choose from.

This type of exterior finish, in addition, radically solves the problem of thermal insulation of the frame. The only thing we recommend at the same time is to glue the panels onto polyurethane foam glue or polyurethane mounting foam with maximum filling of the contact area with the wall.

Wet facade on the frame house

The “wet facade” technology is not so much different in the version for the carcasses, as it has some peculiarities. Namely – not worth it:

  1. glue polystyrene foam or basalt on cement mixtures to OSB – use polyurethane glue or foam;
  2. use wood screws for mounting and either large diameter plastic washers or caps from fungi – the fungus itself keeps badly in the slab; in case of mounting it is foam, you can remove the fastener after its polymerization.

The remaining procedures of this technology are common to all types of houses:

  • reinforcement with appropriate adhesive compositions with alkali-resistant plastic mesh in 1 or 2 layers;
  • primer;
  • putting a finishing plaster layer (fur coat, bark beetle other);
  • painting.

Plastering the walls of the frame house

When they talk about plastering skeleton carcass, first of all they mean plastering OSB. Immediately make a reservation – this option of the exterior finish can be used either in the case of closing all the seams between the panels with decorative slats (imitation half-timbered), or as a temporary option to protect the facade before its final design.

No way to seal the seams will prevent the occurrence of cracks on them. Therefore, choosing this type of finish, do not waste any effort, time or money on the method described in many articles with gluing serpyanka, filling with elastic sealants, etc.

Ground the walls with a deep penetration primer, fix the alkali-resistant mesh with a stapler and plaster with spatulas. It is better to use special elastic plaster for OSB – already several Russian factories produce such.

Next – either paint the surface, or apply a layer of decorative plaster, or close the seams with decorative slats, or be ready for the occurrence of cracks. Choose you.

Other types of facade finish frame house

Along with the previous method, other thin-layer coatings for OSB are often used – dyeing or coating with various polymeric materials with or without inclusion of fine stone powder.

Obviously, you need to paint compositions intended for applying it on the OSB. You will find a lot of such materials on the Internet, with your own layouts and laying techniques. Do not experiment with untested materials – more expensive.

The polymeric compositions used for applying to OSB, have either an acrylate or polyurethane base. The first ones tolerate prolonged exposure to water worse and, even those painted in bulk, will last for a long time with an additional water-repellent outer coating.

As a filling in them, small fractional quartz most often serves. It is more convenient to apply them with a hopper gun. Polyurethane compounds allow the addition of cement, are applied, as a rule, with spatulas rather thick (up to 3 mm) layer. They can be pressed into a larger filler, such as dust-free granotsev or marble chips.

These types of finishes completely hide the structure of the OSB and give a solid look to the house. True problem with the seams between the panels may arise as well.

Exterior finish frame house | Choose the most suitable option

The times when a tree was considered a warm material have sunk into oblivion. To prevent heat transfer through a wooden wall, its thickness should be at least 530 mm. for central Russia. The frames of individual houses are made mainly of wood, and sometimes metal structures are used, which makes the problem even more acute. Therefore, the exterior finish of the frame house, besides the purely aesthetic, often performs an important technological function – it insulates wood (or metal) of the frame, which itself serves as a cold bridge. Of course, in this article we will also consider finishing options that ignore this fact, but we don’t have the right to mention it.

Than outside trim frame house

There are no special restrictions on the exterior finish of the frame house, there are some features of the application of one or another of its type, which we will inform you about. Frame houses revet:

with a wet facade system,

  • plaster;
  • stained;
  • put polymeric coverings.

You should make the decision on one or another type of exterior finish at home at the design stage, as some of them start at the foundation laying stage.

Facing the skeleton brick

If you have decided that your frame house externally should seem brick, then one of the options is covering it with natural brick. The main requirement here is the presence of a gap of 30–50 mm between the wall of the house and the inside of the brickwork and the air vents that ensure air circulation in this gap. If this is not done, then moisture will inevitably condense on the inner surface of the brick during the cold season, which ultimately will lead to its accelerated destruction. Nor will she be spared by the outer enclosing material of the frame itself, which is often OSB or plywood.

Naturally, both the width and the bearing capacity of the foundation with this type of finish are adjusted upwards. In general, these are two different systems of housing construction and you should, when combining them, try to avoid hard ties between the frame that does not give shrinkage and the brick coat that sits down during the year. The consequences can be sad.

You can disguise this with a lowered overhang of the roof that is not connected to the brickwork. Also, either set aside for the time being the manufacture of exterior window and door slopes, or do not rigidly connect them with the masonry. It can be metal or plastic corners.

Facing a frame house with a tree

Correct lining with wooden moldings, such as block house, false timber, etc. will give your home a stylish look. Using them can also eliminate the outer lining of OSB, plywood or other slab material from the cake of the wall. A textured wooden bar, well dried and treated with necessary impregnations, can be directly attached to the racks of the house frame from the inside, before laying the insulation layer, as well as on the clamps or through self-tapping screws – after it. Bearing in mind that the tree can be a cold bridge, we can recommend this mount in the case of the construction of a double frame, with a shift of racks relative to each other.

Also, the wood frame decoration with wooden elements can be made on the crate with a ventilation gap. It is important to remember that such a facade of your house will require periodic maintenance, which consists in the timely processing of paint-impregnating materials. And, of course, the tree will crack somewhere, somewhere in the sunny side the gap in the joints will increase. To this you just need to be ready, choosing this option of exterior home decoration.

The remaining procedures of this technology are common to all types of houses:

  • reinforcement with appropriate adhesive compositions with alkali-resistant plastic mesh in 1 or 2 layers;
  • primer;
  • putting a finishing plaster layer (fur coat, bark beetle other);
  • painting.

Plastering the walls of the frame house

When they talk about plastering skeleton carcass, first of all they mean plastering OSB. Immediately make a reservation – this option of the exterior finish can be used either in the case of closing all the seams between the panels with decorative slats (imitation half-timbered), or as a temporary option to protect the facade before its final design. No way to seal the seams will prevent the occurrence of cracks on them. Therefore, choosing this type of finish, do not waste any effort, time or money on the method described in many articles with gluing serpyanka, filling with elastic sealants, etc.

Ground the walls with a deep penetration primer, fix the alkali-resistant mesh with a stapler and plaster with spatulas. It is better to use special elastic plaster for OSB – already several Russian factories produce such.

Next – either paint the surface, or apply a layer of decorative plaster, or close the seams with decorative slats, or be ready for the occurrence of cracks. Choose you.

Other types of facade finish frame house

Along with the previous method, other thin-layer coatings for OSB are often used – dyeing or coating with various polymeric materials with or without inclusion of fine stone powder.

Obviously, you need to paint compositions intended for applying it on the OSB. You will find a lot of such materials on the Internet, with your own layouts and laying techniques. Do not experiment with untested materials – more expensive.

The polymeric compositions used for applying to OSB, have either an acrylate or polyurethane base. The first ones tolerate prolonged exposure to water worse and, even those painted in bulk, will last for a long time with an additional water-repellent outer coating. As a filling in them, small fractional quartz most often serves. It is more convenient to apply them with a hopper gun. Polyurethane compounds allow the addition of cement, are applied, as a rule, with spatulas rather thick (up to 3 mm) layer. They can be pressed into a larger filler, such as dust-free granotsev or marble chips.

These types of finishes completely hide the structure of the OSB and give a solid look to the house. True problem with the seams between the panels may arise as well.

Dear readers, if you have any questions, ask them using the form below. We will be glad to communicate with you ��

11/23/2016 at 10:53

Question:
how does the insulation (wool) behave when upholstered from OSB (plywood) along the frame?
it is known that impregnation gives water resistance to these products, which makes them practically vapor proof
and the second question. why under the brick lining need wind protection?

11.27.2016 at 14:35

1. More than 90% of the OSP boards are wood, and up to 7% of the resins contained in them will not provide the vapor impermeability you mention. In addition, when stitching OSB temperature joints are required. A superdiffusion membrane must be installed between cotton wool and OSB, otherwise it will inevitably be wetted. In addition, when using wadded insulation and house covering OSB, in addition to the membrane, there should also be a ventilation gap, as in the method described in the article for block-block or false-bar finishing. Thus, it is necessary to remove excess moisture from the inner surface of the OSB (wood), and from the insulation that has penetrated into it from the inside in the form of steam. Without ventzazor, you can sheathe the frame of the house, insulated with polystyrene foam glued to the OSB, almost not permeable to moisture. In this case, there is no room for moisture to condense. But at the same time you should either make a double skeleton or stick a layer of expanded polystyrene on the outside in order to avoid cold bridges on the tree.
2. When facing a frame house with a brick, in winter it will freeze to the full thickness, and from the house in any case heat comes from the back side. So on the inner surface of the brick water will inevitably condense. Partially, it will be absorbed by the brick itself, and partly it will want to be absorbed into the wadded insulation. To counteract this and should vetrovlamozashchita in the form of a super-diffusion membrane that permits moisture only in the form of steam from the wall and does not give moisture in the form of condensate (water) to penetrate into it. And the barrier to the half-brick for the wind is not an obstacle. Even a wall and a half brick lets wind. And we do not need to blow microparticles from cotton inside the room. They are so small that they will find a way for themselves if we do not protect ourselves from this.

Comments and questions from readers

Sources: http://karkasblog.ru/mounting/naruzhnaya-otdelka-karkasnogo-doma.html, http://chudoogorod.ru/t12/varianty-naruzhnoj-otdelki-karkasnogo-doma.html, http: // stroi- specialist.ru/karkasnoe-domostroenie/naruzhnaya-otdelka-karkasnogo-doma-vybiraem-iz-mnozhestva-variantov.html

Add a Comment

Your email address will not be published. Required fields are marked *